110 Series Injector On‑Engine Puller — Controlled Extraction Force For Taper‑Seated Nozzles
video
110 Series Injector On‑Engine Puller — Controlled Extraction Force For Taper‑Seated Nozzles

110 Series Injector On‑Engine Puller — Controlled Extraction Force For Taper‑Seated Nozzles

1. Product:110 Series Injector On‑Engine Puller
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: Original :ABOSEDE DIESEL
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal

  • Fast Delievery
  • Quality Assurance
  • 24/7 Customer Service
Product Introduction

In the 110 series injector family (widely used in Sino‑truck, Weichai, and FAW heavy‑duty common rail engines), the injector nozzle is retained in the cylinder head bore via a tapered interference fit combined with carbon‑induced adhesion. Conventional extraction methods-hammering with a slide hammer or prying with a crowbar-apply impact loads that can reach 2,500 N in a 5‑millisecond spike, often deforming the injector body's upper sealing shoulder or fracturing the ceramic plunger guide. This 110 Series Injector Puller redefines removal as a controlled tensile operation, applying a sustained axial force of up to 4,000 N at a linear rate of 3 mm/second, which overcomes the static friction of carbon‑locked nozzles without subjecting the injector to shock‑induced stress fractures. The result is a higher extraction success rate with zero collateral damage to the cylinder head thread or the injector's precision‑ground outer diameter.

Dual‑Stage Mechanical Advantage System

The puller operates through a two‑stage force multiplier: a manual lead screw for initial preload (0–1,500 N) followed by a planetary gear reducer that amplifies the applied torque by a factor of 8:1, generating the high tensile force for stubborn extractions. The gear train is housed in a sealed, grease‑packed aluminium housing rated for 5,000 cycles without maintenance. The lead screw features a trapezoidal thread (Tr18×3) with a self‑locking angle of 5°, meaning the force is maintained even if the operator releases the handle-a safety feature that prevents sudden recoil when the injector breaks free. The operating handle is a folding T‑bar with a 250 mm lever arm, providing ample leverage while accommodating tight engine bay clearances typical of 110 series installations.

Adaptive Collet and Load Distribution

The puller's interface with the injector is via an interchangeable collet system that grips the injector's upper threaded collar or the annular groove just below the electrical connector, depending on the injector variant. The collet is split into four segments and internally serrated, distributing the clamping force radially to prevent point‑loading that could collapse the thin‑walled injector body. The collet's internal taper matches the injector's collar diameter of Ø 18.0 mm for the mechanical variants and Ø 19.5 mm for the common rail versions; the set includes five collets to cover all 110 series configurations (including the Bosch CP1 and CP3 derivatives). The collet closure is actuated by a cam‑over‑center lever that provides a mechanical advantage of 6:1, ensuring a secure grip with a clamping force of 600 N, far exceeding the 200 N needed to prevent slippage during extraction.

Axial Alignment and Tilt Prevention

One of the primary causes of extraction failure is the injector tilting within the bore, causing the nozzle to jam against the cylinder head wall. The puller incorporates a guide sleeve that slips over the injector body and registers against the cylinder head's counterbore surface. This sleeve ensures the pulling axis remains coaxial with the injector bore within ±0.5° of tilt, even when the operator applies off‑center torque. The sleeve is machined from bronze‑impregnated PTFE to avoid scoring the cylinder head, and its internal clearance is precisely 0.15 mm greater than the injector's OD, allowing for thermal expansion while maintaining guidance. An adjustable level indicator (a spirit vial) on the top plate confirms vertical alignment before commencing the pulling sequence, eliminating the guesswork that leads to binding.

Force Monitoring Without Electronics

Rather than relying on fragile load cells, the puller includes a mechanical force indicator-a calibrated spring‑loaded plunger that displaces proportionally to the applied tensile force, displaying the value on an analog scale from 0 to 5,000 N. This indicator provides real‑time feedback, allowing the technician to gradually increase force and observe when the injector begins to move (a sudden drop in force indicates break‑free). The scale is color‑coded: green zone (0–2,000 N) for routine extractions, yellow (2,000–3,500 N) for carbon‑locked injectors, and red (above 3,500 N) as a warning that the injector may be seized beyond normal extraction limits, signaling the need for chemical penetrant application. This visual feedback reduces the tendency to over‑force and prevents thread stripping in the cylinder head.

FAQ

Q1: Does this puller work on injectors that have been in service for over 15,000 hours with severe carbon buildup?
Yes. The puller's maximum force (4,000 N) is sufficient for most seized injectors. For extreme cases, we recommend applying penetrating oil through the hollow screw and allowing 15 minutes of dwell time before pulling; the combination has successfully extracted injectors with up to 18,000 hours of service in our tests.

Q2: Will the collet damage the injector's electrical connector or the high‑pressure fuel inlet port?
No. The collet grips only the designated mechanical collar or groove, well below the connector area. The guide sleeve also shields the fuel inlet from accidental impact. Ensure you select the correct collet matching the injector variant-using an incorrect collet may contact sensitive areas.

Q3: How do I know if the injector has started moving during the extraction?
The force indicator needle will momentarily drop by 200–300 N as the static friction is overcome, and the handle will feel less resistant. Some operators also place a chalk mark on the injector top and the cylinder head to visually confirm relative movement.

Q4: Can the puller be used on engines where the cylinder head is still installed on the vehicle?
Yes, this is an on‑engine tool. The folding T‑bar and compact frame are designed to fit within engine bay constraints. For extremely tight clearances (e.g., cab‑over trucks), the T‑bar can be removed and replaced with a 3/4" square drive ratchet for lower‑profile operation.

Q5: What should I do if the extraction force exceeds 4,000 N without movement?
Stop immediately. Exceeding this force may damage the cylinder head thread or the injector body. The proper course is to apply solvent through the hollow screw, wait 30 minutes, then re‑attempt. If still stuck, the injector may require head removal and bench pressing-the puller is not intended for welded or hydraulically locked cases.

Q6: Is the tool compatible with 110 series injectors that have been welded or staked in place as an anti‑tamper measure?
No. If an injector has been mechanically staked or welded, this puller will not overcome that retention. We recommend inspecting the injector area for visible anti‑tamper modifications before using the tool-if present, the head must be removed for disassembly.

202510091606539026

 

 

2

3

4

 

Flexible Payment Methods for Your Convenience

 

To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

product-750-750

Bank Transfer

Pay directly in 15 supported currencies.

west union

Western Union

Quick and global money transfers.

PayPalLogo2014-1024x1014

PayPal

Safe and convenient online payment.

ae99cd49-2667-464e-b9db-b39cee0126e1

Alibaba

Enjoy extra protection with trusted Alibaba transactions.

We're here to make your order process worry-free - choose the payment method that works best for you!

 

Shipping Made Simple

6

Customer reviews

 

8

Hot Tags: 110 series injector on‑engine puller — controlled extraction force for taper‑seated nozzles, China 110 series injector on‑engine puller — controlled extraction force for taper‑seated nozzles manufacturers, suppliers, factory

You Might Also Like

(0/10)

clearall