Bosch 0445111180 Common Rail Injector for PSA DW10 & Renault G9T Engines
video
Bosch 0445111180 Common Rail Injector for PSA DW10 & Renault G9T Engines

Bosch 0445111180 Common Rail Injector for PSA DW10 & Renault G9T Engines

1. Product: Common Rail Injector
2. Manufacturer: Bosch
3. Adaptive pump: Bosch CP1 pump
4. Model: 0445111180
5. Condition: Brand New
6. Origin: made-in-Germany
7. Shipping period:3-5 days
8. Payment terms:T/T, Western union, PayPal

  • Fast Delievery
  • Quality Assurance
  • 24/7 Customer Service
Product Introduction

 

The Bosch 0445111180 is a new genuine common rail injector from the CRI 1.2 family, built for PSA DW10/DW12 and Renault G9T diesel platforms. It operates at up to 1,600 bar with a six-hole nozzle and solenoid control, delivering the spray geometry and metering consistency that Euro 4/5 combustion strategies depend on. For workshops and parts distributors, the practical question is rarely "what is it"-it is whether this unit fits the bay, survives the fuel quality, and holds its calibration beyond the first oil change.

 

🔧 What the bench numbers actually tell you before you install

 

A CRI 1.2 injector lives or dies by its hydraulic tolerances, not its cosmetic condition. The 0445111180 carries a solenoid resistance window of approximately 0.255 Ω (tolerance ±0.040 Ω), and the armature residual air gap must sit within the factory band before the ECU can command a clean pilot injection. On the bench, return flow is the tell: a unit that passes a static resistance check but bleeds excess leak-off will trigger P0087 or P1093 codes once rail pressure demand rises under load. The six-hole DLLA nozzle on this injector is calibrated for DW10 chamber geometry; fitting a generic nozzle with the same thread but different spray angle shifts the burn centroid and quietly raises DPF soot loading without throwing a hard fault. The copper washer is a single-use crush seal-reusing one is the fastest way to create a compression leak that mimics an injector failure.

 

📊 Fitment matrix that matters at the parts counter

 

Attribute Specification
Injector family Bosch CRI 1.2 (solenoid)
Bosch part number 0 445 111 180 / 0445111180
Cross-reference PSA 9657144580, 9656335480; Renault 8200399930; Ford 6C1Q-9K546-AA
Engine platforms PSA DW10 / DW12 (Euro 4/5); Renault G9T 1.9L, 2.0L, 2.2L
Vehicle applications Peugeot 407/607/807/Expert; Citroën C5/C8/Jumpy; Renault Espace/Laguna/Trafic/Master; Ford Transit (PSA diesel)
High-pressure pump pairing Bosch CP1 series (0445010049, 0445010090)
Operating pressure Up to 1,600 bar
Nozzle configuration 6-hole, factory-calibrated

 

🛣️ Where this injector earns its keep-and where it fails

 

The DW10 and G9T engines share a reputation for tolerating neglect longer than they should, which is precisely why 0445111180 failures cluster around two operating profiles. Short-haul Trafic and Expert vans that never reach full rail pressure accumulate varnish on the control plunger, causing hot-start hesitation before any code appears. Meanwhile, Master and Espace units under sustained load develop needle seat erosion from water contamination that passes the factory filter-visible as a rising return flow rate at 800–1,200 rpm. A genuine Bosch unit restores the injection timing map the ECU expects; a remanufactured or counterfeit unit with a mismatched IQA/trim code forces the ECU into a permanent adaptation drift that no relearn procedure can correct. 

 

💡 The installation sequence that separates a comeback from a repair

 

The most common installation error on 0445111180 is not torque-it is seat preparation. The copper washer seals against the cylinder head bore, not the injector body. Any carbon ring left in the bore creates a micro-leak that pressurizes the hold-down clamp area and eventually cracks the injector body flange. Clean the bore with a nylon brush, not a metal scraper, and confirm the new washer sits flat before torquing the clamp in two stages. After installation, clear rail pressure adaptation in the ECU and perform a leak-off test at idle and 1,500 rpm before road testing. If return flow exceeds 40 ml/min per injector at idle on a warmed engine, stop-the unit is either defective or the CP1 pump is sending debris downstream. The inlet filter screen on the injector is a last line of defense, not a diagnostic tool; a clogged screen means the pump or filter housing is already shedding material.

 

❓ FAQ for diesel repair shops and parts buyers

 

Q1: Can I mix a new 0445111180 with three existing injectors on the same DW10?
A: Only if the original three pass a leak-off and flow bench test within 5% of each other. Beyond that spread, replace the set-mixed calibration causes uneven pilot injection quantities the ECU cannot trim out.

Q2: The box says "Made in Germany" but the body looks different from my old unit. Counterfeit?
A: Bosch has shifted some CRI 1.2 production between Germany and Turkey without changing the part number. Verify the laser-etched 2D code and IQA code match the calibration certificate-counterfeit batches often share identical trim codes.

Q3: Realistic service life on a Trafic or Expert?
A: With fuel filter changes at 20,000 km, expect 80,000–120,000 km of mixed use. Stop-start delivery work shortens this to around 70,000 km, as the control valve never reaches steady-state temperature to burn off deposits.

Q4: Does it require coding after installation?
A: Yes. The IQA/trim code must be written into the ECU injector classification map. Skipping it lets the engine start but locks in a default strategy that raises NOx and can trigger P2002 on Euro 4 platforms.

Q5: My CP1 pump has 200,000 km-replace it with the injectors?
A: Not automatically. Confirm the pump sustains 1,350 bar at 3,000 rpm under load first; a weak CP1 forces longer injection durations that accelerate needle seat wear on new injectors.

Q6: Best visual check for a genuine unit out of the box?
A: The return port bore and connector pins. Genuine units have a mirror-finished bore with no machining ridges and pins sitting flush; counterfeits show tool marks and unevenly protruding pins.

 

2

 

Meet Abosede

 

1

 

Customer feedback

 

8

 

Flexible Payment Methods for Your Convenience

 

To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

product-750-750

Bank Transfer

Pay directly in 15 supported currencies.

west union

Western Union

Quick and global money transfers.

PayPalLogo2014-1024x1014

PayPal

Safe and convenient online payment.

ae99cd49-2667-464e-b9db-b39cee0126e1

Alibaba

Enjoy extra protection with trusted Alibaba transactions.

We're here to make your order process worry-free - choose the payment method that works best for you!

 

Shipping Made Simple

 

We understand that every customer has unique shipping needs. That's why we offer:

1

Global Express Services

DHL, FedEx, UPS for fast and secure delivery.

Sea freight

Sea Freight Solutions

Affordable and efficient for bulk orders.

freight forwarder001

Flexible logistics

Prefer your own forwarder? We're happy to work with them too.

No matter the destination, we tailor the best shipping solution for you.

 

📞 Need Help?

 

Abosede Diesel offers OEM-quality fuel system parts for Cummins, Bosch, CAT, and Denso platforms. Contact us for bulk pricing, technical specifications, or compatibility checks with your engine.

Hot Tags: Bosch 0445111180 Common Rail Injector for PSA DW10 & Renault G9T Engines, China Bosch 0445111180 Common Rail Injector for PSA DW10 & Renault G9T Engines manufacturers, suppliers, factory, bosch injector

You Might Also Like

(0/10)

clearall