Bosch 0445120231 Injector for Komatsu 6D107 & Cummins QSB6.7

Bosch 0445120231 Injector for Komatsu 6D107 & Cummins QSB6.7

1. Model number: 0445120231
2. Weight: 0.8 kg
3. Material: Iron
4. Condition: new
5. Origin: China
6. Application: for QSB4.5 Engine

  • Fast Delievery
  • Quality Assurance
  • 24/7 Customer Service
Product Introduction

 

This Bosch common rail injector 0445120231 (cross-reference 0445120059 / 6754-11-3011) is the solenoid-actuated fuel delivery unit used across the Komatsu 6D107 and Cummins QSB6.7 engine families. It operates within a high-pressure common rail circuit reaching 160–180 MPa, executing up to five injection events per combustion cycle-pilot, pre, main, post, and after-to balance cold-start noise, torque output, and particulate matter control under Tier 3 / Stage IIIA emission regimes.

 

🔩 What the Numbers on the Box Actually Tell You

 

Specification Detail
Bosch part number 0445120231
Cross-references 0445120059 / 6754-11-3011 / 5263262 / 3976372
Injector family Bosch CRI2 (solenoid-controlled)
Engine platforms Komatsu 6D107 / 4D107; Cummins QSB6.7 / QSB4.5
Operating rail pressure 160–180 MPa (approx. 1600–1800 bar)
Injection events per cycle Up to 5 (pilot / pre / main / post / after)
Emission compliance Tier 3 / Stage IIIA
Solenoid resistance (nominal) ≈ 0.3–0.6 Ω at 20°C (verify against OEM spec)
Critical installation value IQA / trim code (5-digit) - must be programmed post-install

 

🛣️ Where This Injector Actually Lives: Machine Applications Beyond the Catalogue Dropdown

 

The 0445120231 is not a universal fit, and treating it as such is how mismatched parts end up in the wrong engine bay. Its highest-volume real-world deployment is the Komatsu PC200-8, PC210-8, PC220-8, and PC240-8 excavator series running the 6D107 six-cylinder engine. In the Cummins ecosystem, the same injector serves QSB6.7 powered wheel loaders, including the Komatsu WA320-6 and WA380-6, as well as Case CX210B / CX240B excavators that use the Cummins variant of the 6.7L platform. The four-cylinder 4D107 in machines like the PC130-8 and PC160-8 uses the same injector design but requires only four units per engine-confirm cylinder count before quoting a set. Articulated haulers such as the HM300-2 and HM350-2 also appear in the compatibility matrix. What most parts lookups omit is the industrial and generator segment: stationary power units built on the 4D107/6D107 base engine take this injector as well, though fuel quality and governor strategy in genset applications often accelerate internal deposit formation compared to mobile equipment that sees regular load cycling.

 

🧩 Installation Reality: Why the Second Comeback Usually Traces Back to the Bore

 

A fresh injector installed into a compromised cylinder head bore is a warranty claim waiting to happen. The 0445120231 seals against combustion pressure via a copper washer at the nozzle tip, and the bore depth and surface flatness must be verified before the clamp is torqued-carbon buildup at the seating surface creates a leak path that manifests as hard-start and white smoke within weeks. The high-pressure connector tube is a one-time-use component: reusing the old tube is the single most common cause of fuel dilution in the oil after an injector replacement, because the tube's sealing shoulder work-hardens and will not re-conform under torque. Program the IQA code with a diagnostic platform capable of writing to the ECM-Cummins INSITE or Komatsu EMMS-before attempting to start the engine. After programming, prime the rail and monitor rail pressure build rate during cranking; a lazy pressure curve indicates air ingress or a failing pressure control valve, not a defective injector.

 

💡 The Repair Economics: When This Injector Makes Sense for a Shop

 

For an independent diesel repair facility, the 0445120231 occupies a specific economic lane. A Komatsu PC200-8 or QSB6.7 powered machine showing SPN 651–656 / FMI 7 (injector mechanical fault) or a cylinder balance rate exceeding ±3 mm³/stroke on a INSITE or EMMS diagnostic session is a candidate for injector replacement-but only after ruling out return flow from a worn pressure relief valve and confirming that the fuel filter housing is not passing debris downstream. The counterfeit risk in this part number is real: identical IQA codes across multiple injectors in one box is the clearest signal of a non-genuine product, and shops have reported engines running worse after installing "too cheap to be true" units. The repair value proposition is not the part price-it is the downtime avoidance on a production excavator or a haul truck that costs hundreds per hour in lost output. Purchasing from a supplier who can provide a bench test report with flow rates at multiple pressure points, rather than a generic "quality assured" claim, is the practical filter for separating a usable aftermarket unit from a future failure.

 

❓ FAQ: Sourcing and Service Questions from Diesel Shops

 

Q1: The engine runs but shows a cylinder 3 contribution code only at operating temperature. Is the injector electrically failing?
A: Temperature-dependent misfire usually points to a solenoid coil breaking down when hot, not a nozzle issue. Ohm-test the injector cold and again after warming the engine; a resistance shift beyond the OEM window confirms the coil is failing and the unit needs replacement rather than cleaning.

Q2: Can I mix this injector with an 0445120059 in the same engine if both cross-reference?
A: Physically they interchange, but the IQA codes are unique to each injector. If you install a mixed set, each unit's individual trim must be programmed. A shop that lacks the diagnostic capability to write codes should install a matched set from the same production batch to minimize balance drift.

Q3: What is the most reliable return-flow threshold for condemning this injector?
A: Bosch specifies a maximum back-leak volume per unit time at defined rail pressure; exceeding it by more than 15–20% across multiple cylinders means the control valve seat is worn. Testing one injector in isolation is misleading-always compare return flow across all cylinders on the same engine before condemning a single unit.

Q4: How do I verify authenticity before installing?
A: Check the IQA code on the injector body against the code on the box label. A genuine unit carries a unique code; duplicate codes across a set indicate counterfeit product. Also inspect the nozzle tip under magnification-genuine Bosch nozzles have consistent spray hole geometry with no burrs or asymmetrical erosion.

 

Flexible Payment Methods for Your Convenience

 

To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

product-750-750

Bank Transfer

Pay directly in 15 supported currencies.

west union

Western Union

Quick and global money transfers.

PayPalLogo2014-1024x1014

PayPal

Safe and convenient online payment.

ae99cd49-2667-464e-b9db-b39cee0126e1

Alibaba

Enjoy extra protection with trusted Alibaba transactions.

We're here to make your order process worry-free - choose the payment method that works best for you!

 

Shipping Made Simple

 

We understand that every customer has unique shipping needs. That's why we offer:

1

Global Express Services

DHL, FedEx, UPS for fast and secure delivery.

Sea freight

Sea Freight Solutions

Affordable and efficient for bulk orders.

freight forwarder001

Flexible logistics

Prefer your own forwarder? We're happy to work with them too.

No matter the destination, we tailor the best shipping solution for you.

 

Hot Tags: Bosch 0445120231 Injector for Komatsu 6D107 & Cummins QSB6.7, China Bosch 0445120231 Injector for Komatsu 6D107 & Cummins QSB6.7 manufacturers, suppliers, factory, bosch injector

You Might Also Like

(0/10)

clearall