1000943153/20194A Fuel Transfer Pump – Low-Pressure Feed Unit For Common Rail Diesel Supply Circuits
video
1000943153/20194A Fuel Transfer Pump – Low-Pressure Feed Unit For Common Rail Diesel Supply Circuits

1000943153/20194A Fuel Transfer Pump – Low-Pressure Feed Unit For Common Rail Diesel Supply Circuits

1. Product:1000943153/20194A
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: ABOSEDE Diesel
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal

  • Fast Delievery
  • Quality Assurance
  • 24/7 Customer Service
Product Introduction

 

Rail pressure begins long before the high-pressure plunger moves. The 1000943153/20194A transfer pump establishes the inlet condition that decides whether the high-pressure pump can fill completely, avoid cavitation, and follow ECU pressure requests. This is a low-pressure fuel supply pump, not a high-pressure generator. Its function is to deliver a stable, air-free, filtered diesel stream at the correct inlet pressure to the high-pressure pump.

 

⛽ Low-Pressure Circuit Hydraulic Task

 

The 1000943153/20194A sits between the tank, pre-filter, water separator, and high-pressure pump inlet. It supplies positive pressure-typically 4–6 bar-so the high-pressure pump does not draw fuel under vacuum. Vacuum promotes vapor formation, especially with hot fuel or restricted filters. By maintaining inlet pressure, the transfer pump improves volumetric efficiency, reduces cavitation erosion on plungers and outlet valves, and supports stable rail pressure during cranking and load transients.

 

📊 Flow, Pressure & Electrical Parameters

 

Typical working data for this transfer pump family: delivery pressure 4–6 bar; flow 1.8–2.5 L/min at rated voltage; voltage 12 V or 24 V depending on application; current draw 3–6 A at 12 V; operating temperature -30°C to +90°C; inlet vacuum limit 0.3 bar; filtration 5–10 µm pre-filter and 3–5 µm final. Pressure holding after key-off should remain above 2.5 bar for 10 minutes. If pressure drops faster, check check valve, seals, or internal wear. These values are diagnostic references; always confirm against OEM data.

 

🧲 Internal Sealing & Wear-Resistant Architecture

 

The 1000943153/20194A uses a positive-displacement pumping element-roller vane, gear, or diaphragm depending on OEM build-driven electrically or mechanically. A relief valve protects the low-pressure circuit from overpressure. An integrated check valve prevents backflow and keeps the high-pressure pump inlet primed. Seal materials must resist diesel, biodiesel, and cold-flow additives. The housing and end cover are machined to control axial clearance; excessive clearance reduces flow and increases noise. Do not reuse crushed sealing washers.

 

🌡️ Thermal Behavior & Fuel Viscosity Response

 

Cold diesel has higher viscosity and higher resistance to flow. The 1000943153/20194A must overcome this without exceeding inlet vacuum limits. At -20°C, wax crystals can block the pre-filter, causing low pressure and hard starting. At high temperature, lower viscosity increases internal leakage and reduces delivery. The pump therefore works within a viscosity window; if the fuel is too thick or too thin, ECU rail pressure control may deviate. Use a heated pre-filter in extreme cold and monitor fuel temperature sensor data.

 

🧪 Particulate Tolerance & Filtration Requirements

 

Contamination is the primary enemy of common rail low-pressure circuits. Particles between 5 and 10 µm can lodge in the transfer pump and high-pressure pump inlet. Water causes corrosion and lubricity loss. The 1000943153/20194A should be paired with a water separator and a filter rated at 3–5 µm absolute. Replace filters at 20,000–30,000 km, or 15,000 km with B20/B30 biodiesel. A rising filter differential pressure can starve the transfer pump and create cavitation even if the pump itself is healthy.

 

❓ FAQ – Buyer & Technician Questions

 

Q1: Is 1000943153/20194A an electric or mechanical pump?
A: Depending on OEM build, it can be supplied as electric or mechanical. Check connector and drive type before ordering. The number alone may have variants.

Q2: What pressure should it produce?
A: Typically 4–6 bar. It must hold above 2.5 bar for 10 minutes after key-off. Lower values indicate check valve or internal leak.

Q3: Can I use it with B20/B30 biodiesel?
A: Yes if fuel meets EN 14214 or ASTM D6751. Shorten filter intervals. Monitor inlet pressure and seal condition.

Q4: Why does the pump become noisy after filter change?
A: Air may be trapped. Bleed low-pressure circuit. Also check filter micron rating; too fine a filter can increase inlet vacuum.

Q5: What causes cavitation in the high-pressure pump?
A: Restricted filter, tank pickup, or weak transfer pump. Inlet vacuum above 0.3 bar promotes vapor bubbles and erosion.

Q6: Does it require ECU programming?
A: No. It is a low-pressure supply component. No coding is required. However, if rail pressure adaptation is stored, clear faults after repair.

 

Basic Information about the Company

 

Abosede at the exhibition – group photo for the memories.

 

 

Global Reach

Global Reach

Global Reach

 

Flexible Payment Methods for Your Convenience

 

To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer

Bank Transfer

Pay directly in 15 supported currencies.

Western Union

Western Union

Quick and global money transfers.

PayPal

PayPal

Safe and convenient online payment.

Alibaba

Alibaba

Enjoy extra protection with trusted Alibaba transactions.

We're here to make your order process worry-free - choose the payment method that works best for you!

 

Shipping Made Simple

Shipping Made Simple

Customer reviews

 

Customer Reviews

Hot Tags: 1000943153/20194a fuel transfer pump – low-pressure feed unit for common rail diesel supply circuits, China 1000943153/20194a fuel transfer pump – low-pressure feed unit for common rail diesel supply circuits manufacturers, suppliers, factory, 0470504031 pump for Isuzu 4JH1 Engines, 0470504048 pump for Isuzu 4KH1 Engines, 380-7923, DB4429 5694 RE504066 pump, generator, Perkins Engines

You Might Also Like

(0/10)

clearall