2057401 Armature Plate – Bosch Common Rail Injector Control Valve Magnetic Armature
1. Product:2057401 Armature Plate
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: ABOSEDE Diesel
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
The magnetic circuit inside a CRDI control valve behaves like a micro air-gap actuator. The 2057401 armature plate sits at the center of that air gap. It converts solenoid force into valve lift, and its thickness, flatness, and surface condition determine how quickly and consistently the control valve opens. When this plate wears, deforms, or loses its magnetic properties, the electrical signal no longer matches hydraulic response. Injection timing drifts, return flow rises, and cylinder balance suffers-often before any hard fault code appears.
🧲 Magnetic Air-Gap Function
In a Bosch common rail injector, the control valve solenoid pulls the armature plate against spring force. The plate moves a small distance, usually 0.05–0.15 mm, to open or close the control chamber return path. This movement is not a simple mechanical stroke. It is a magnetic energy conversion cycle. The 2057401 armature plate must provide high magnetic permeability, low hysteresis, and stable flatness. If the air gap changes by even a few hundredths of a millimeter, the current-to-lift relationship changes. The ECM may still command the same pulse, but the hydraulic result is different.
📏 Critical Dimensions and Data
Typical 2057401 armature plates use soft magnetic iron or silicon steel. Thickness often falls between 0.8 and 1.5 mm depending on control valve generation. Flatness is commonly held to ≤0.005 mm. Surface roughness may be Ra ≤0.4 µm to reduce magnetic loss and wear. Hardness often ranges from 200 to 300 HV. Coating may be nickel or zinc flake for corrosion resistance. The control valve coil usually measures 0.2–0.5 ohms at 20°C and is driven by peak-and-hold current: peak 15–20 A, hold 5–8 A. Rail pressure can reach 1,800–2,000 bar, and fuel temperature exposure commonly spans −40°C to +140°C.
🧪 Material, Coating and Contamination
The armature plate is a wear surface and a magnetic conductor. It must resist adhesion, corrosion, and fatigue. Water, rust, and particles above 5 µm accelerate surface damage. Diesel filtration should target 2–5 µm. Biodiesel blends can be used if they meet fuel standards, but oxidation and water absorption increase risk. Never polish the armature plate with abrasives. That changes thickness, flatness, and air gap. Clean bench work and new seals are mandatory during replacement.
🚗 Fitment and Cross-Reference Logic
The 2057401 armature plate is referenced for Bosch common rail injectors using the 2057401 control valve family. Applications include passenger cars, light commercial vehicles, and selected industrial diesel engines. Fitment must be confirmed by injector number, control valve number, and OEM cross-reference-not by engine model alone. Bosch control valves have multiple generations. Plate diameter, thickness, center hole, and coating can differ. If the old plate shows a different profile, stop and verify before assembly.
❓ FAQ
Q1: Can I replace only the 2057401 armature plate without changing the whole control valve?
Yes, if the valve seat, spring, and solenoid are within specification. However, the injector must be recalibrated on a test bench.
Q2: How do I know the armature plate is worn?
Look for flatness loss, corrosion pits, edge deformation, or shiny wear tracks. A bench test showing slow valve response or high return flow also points to plate wear.
Q3: Does armature plate thickness affect injection quantity?
Yes. Thickness changes the air gap and magnetic force. Even a small deviation can shift valve opening delay and minimum injection quantity.
Q4: Is bench testing mandatory after replacing the armature plate?
It is strongly recommended. Idle quality alone cannot confirm correct return flow, back-leakage, or correction values.
Q5: Can I mix armature plates from different control valve generations?
No. Diameter, thickness, center hole, and coating can differ. Always match by injector number and control valve number.
Q6: What fuel factors shorten armature plate life?
Water, rust, fine particles, and aggressive additives. Clean fuel and 2–5 µm filtration reduce wear and keep the air gap stable.
Basic Information about the Company




Flexible Payment Methods for Your Convenience
To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer
Pay directly in 15 supported currencies.

Western Union
Quick and global money transfers.

PayPal
Safe and convenient online payment.

Alibaba
Enjoy extra protection with trusted Alibaba transactions.
We're here to make your order process worry-free - choose the payment method that works best for you!
Shipping Made Simple

Customer reviews

Hot Tags: 2057401 armature plate – bosch common rail injector control valve magnetic armature, China 2057401 armature plate – bosch common rail injector control valve magnetic armature manufacturers, suppliers, factory, abosede accessories
You Might Also Like
-

Bosch CP401 Fuel Pump Service Kit – Feed-Forward Pre...
-

C9.3 Injector Reconditioning Matrix | Precision Seal...
-

09356 Injector Sealing Ring – Micro-Sealing Accuracy...
-

Premium Diesel VE Pump Governor / Regulating Shaft 0...
-

C7/C9 Actuation Pump Gasket Kit 319-0678: What Shops...
-

Toyota 1KD-FTV Engine Assembly: Accessory Transfer I...


