DLLA140P2694 Nozzle for Bosch 0445120568 / Cummins ISB6.7
1.Model number:DLLA140P2694
2. warranty:6 months
3.material : Iron
4.condition : new,LIWEI
5.origin : China
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
This DLLA140P2694 nozzle is the LIWEI-brand replacement element for the Bosch 0445120568 injector body, most frequently encountered in Cummins ISB6.7 commercial applications as well as select European diesel platforms. It is not a universal diesel nozzle. The 140° spray cone and P2694 flow designation are calibrated as a matched pair with the injector's internal hydraulics, meaning the nozzle's seat geometry, needle lift, and sac volume are engineered to work within the specific delivery window of that injector family. For workshops and parts distributors, the practical question is never "is this the cheapest nozzle"-it is whether the replacement will restore the injector to its original flow balance without triggering new fault codes or comebacks.
🔧 Specification Boundaries That Determine Fit
| Parameter | Value |
|---|---|
| Nozzle type | DLLA (long-stem, long guide) |
| Spray cone angle | 140° |
| Bosch internal code | P2694 |
| Matched injector | 0445120568 / 5521671 |
| Typical application family | Cummins ISB6.7, select VW/Audi PD |
| Nozzle material | High-speed steel, hardened needle guide |
| Warranty (LIWEI brand) | 6 months |
🚗 Where This Nozzle Actually Lands in the Field
The DLLA140P2694 is most often pulled from Cummins ISB6.7 injectors in medium-duty freight and vocational equipment, where the injector body carries the 0445120568 or 5521671 stamping. A persistent confusion in aftermarket listings is the claim that this nozzle exclusively serves VW/Audi PD engines. While the Bosch injector family has European roots, the Cummins ISB6.7 application is the dominant service demand in North American and export markets for this part number. Repair shops should verify the injector body number rather than trusting vehicle-level fitment guides alone. The same nozzle may appear in other Bosch 0445120xxx injector variants, but flow matching across variants is not guaranteed without bench verification.
🛣️ Installation Variables That Cause Repeat Failures
The most expensive mistake with this nozzle is installing it into a contaminated injector body. The long guide design of the DLLA series is unforgiving of particulate residue in the injector's control chamber; even microscopic debris that survives cleaning will accelerate needle seat erosion and produce white smoke at idle within a few thousand kilometers. Before fitting, the injector body should be ultrasonically cleaned and the copper washer replaced without exception. Torque values vary by injector clamp design, but the nozzle retaining nut on this family should never be tightened beyond the Bosch specification for the specific injector body-over-torque distorts the spray hole geometry and creates an unbalanced spray pattern that no amount of ECU adaptation can correct. After assembly, a leak-off test at 200 bar is the minimum validation; a nozzle that passes visual spray inspection but fails leak-off will still trigger P1248 or rough-running complaints.
🧩 The Repair Economics Distributors Should Understand
For a diesel parts distributor, the DLLA140P2694 occupies a useful economic position: it is a consumable wear item with predictable replacement intervals, but its failure mode is gradual rather than catastrophic. A nozzle that has drifted 8% or more in flow relative to its cylinder mates will not strand a truck, but it will generate fuel dilution, elevated EGT, and repeat diagnostic labor that erodes shop profitability. The alternative to nozzle replacement-full injector replacement-carries a significantly higher parts cost and often requires programming that older ISB6.7 platforms handle less gracefully. LIWEI's positioning of this nozzle with a 6-month warranty is commercially reasonable for a wear component, but the warranty has little practical value unless the installer can demonstrate clean bench validation. Distributors who pair this nozzle with copper washers and injector seal kits in a single SKU solve a real procurement friction point: shops rarely order every small seal they need, and missing a washer is the most common cause of a comeback on a nozzle job.
❓ FAQ for Diesel Repair Shops and Parts Wholesalers
Q1: Can I use this nozzle in an injector stamped 0445120567 instead of 0445120568?
A: The two injector bodies are closely related and share nozzle family compatibility, but flow classification must be confirmed against the injector's Bosch data sheet. Do not assume interchangeability based on part-number proximity alone; bench-test the assembled injector before installation.
Q2: How do I distinguish a genuine LIWEI DLLA140P2694 from a repackaged low-grade nozzle?
A: Check the needle guide surface under magnification. Genuine LIWEI units show consistent sub-micron grinding with no axial scoring. Counterfeit or reject nozzles often have visible polishing marks perpendicular to needle travel, and their spray holes may show inconsistent taper when backlit.
Q3: What is a realistic service life expectation in ISB6.7 fleet use?
A: Under normal filtration and fuel quality, 150,000–200,000 km is a reasonable planning figure. Fleets running high water content or extended filter intervals should shorten that estimate and consider mid-interval leak-off checks rather than waiting for driveability symptoms.
Q4: Does replacing only one nozzle risk flow imbalance across the engine?
A: Yes. If the remaining five injectors have accumulated wear, a single fresh nozzle can create a cylinder-to-cylinder deviation that the ECU cannot fully adapt. For high-mileage engines, flow-test the existing set or plan for matched replacement in pairs or full sets.
Q5: What bench result disqualifies a freshly assembled injector with this nozzle?
A: Leak-off exceeding 20 ml/min at 200 bar, or a spray pattern with a visible stream or heavy off-axis plume. Either condition indicates seat damage or guide misalignment that will not resolve with ECU adaptation.
Core Strength

Warehouse Photo


Your doubts


Abosede Diesel

Customer feedback

Flexible Payment Methods for Your Convenience
To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer
Pay directly in 15 supported currencies.

Western Union
Quick and global money transfers.

PayPal
Safe and convenient online payment.

Alibaba
Enjoy extra protection with trusted Alibaba transactions.
We're here to make your order process worry-free - choose the payment method that works best for you!
Shipping Made Simple
We understand that every customer has unique shipping needs. That's why we offer:

Global Express Services
DHL, FedEx, UPS for fast and secure delivery.

Sea Freight Solutions
Affordable and efficient for bulk orders.

Flexible logistics
Prefer your own forwarder? We're happy to work with them too.
No matter the destination, we tailor the best shipping solution for you.
Hot Tags: DLLA140P2694 Nozzle for Bosch 0445120568 / Cummins ISB6.7, China DLLA140P2694 Nozzle for Bosch 0445120568 / Cummins ISB6.7 manufacturers, suppliers, factory, F00VX50175 for 0445120287 0445120288 0986435624, DLLA155P848G for Denso, G3S29 for 295050 1710 8 98238318 0 8 98076995 2 01S01513J, F00VX20018 for 0 445115043 0445115059 0445115060, F00VX30002 for 0445115007 0986435350 0986435426, M0502 P147 for 5WS40087 A2C59511606
You Might Also Like
-

Liwei F00VX40072 Piezo Nozzle for Bosch 0445116048/0...
-

DLLA134P2367 Nozzle for Mitsubishi 4M40 & 4D56T Fuel...
-

DLLA150P2125 For 0445110356 YUCHAI LIWEI High Qualit...
-

Liwei Nozzle DLLA140P2483 Common Rail Diesel Injecto...
-

Common Rail Liwei Nozzle DLLA150P2249 For DOOSAN Eng...
-

DLLA140P2303 (0433172303) Nozzle for 0445110457 Inje...




