DLLA150P1712 Nozzle for Bosch 0445120117 (XICHAI 6DN/6DF): Replacing the Nozzle Invalidates the Injector Trim Code, and No Scan Tool Can Recreate It
1.Model:DLLA150P1712
2.Injector:0445120117
3.Engine:XICHAI
4.Brand:Liwei
5.Type: Common rail injector nozzle
6.Usage: Improves fuel atomization and efficiency
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
A DLLA150P1712 nozzle is sold as a wear part for the Bosch 0445120117 injector used on XICHAI 6DN and 6DF engines, with the Bosch cross-reference 0433172049. The listing describes the replacement procedure and then says the injector codes must be rewritten to the ECU. That sentence is the problem. The trim code belongs to the complete injector as it was tested on a bench, not to the nozzle, and replacing the nozzle changes the flow the code describes. A scan tool can write a code into an ECM, but it cannot create a correct code for a combination that has never been tested.
🔢 What the trim code actually describes
The trim code is a compressed record of the injector's measured delivery at several operating points. It is generated when the complete assembly - body, control valve, nozzle and spring - is run on a calibration bench. The ECM uses it as the baseline for every quantity calculation it makes. When the nozzle is replaced, the delivery changes, and the code no longer describes the hardware it is attached to. The ECM then applies a correction that was measured on a different nozzle, and the cylinder runs at a quantity nobody has verified.
🧪 What has to happen instead of "rewriting"
The correct sequence is bench first, code second. The rebuilt injector is run on a common rail injector bench at several rail pressures and pulse widths, the delivery is measured, and a new code is generated from those measurements. Only then is the code written to the ECM. A workshop without a bench cannot complete this step, and a workshop that skips it is running an unverified cylinder. This is the single most important consequence of nozzle replacement, and it is the step the listing compresses into one sentence.
🔬 The four nozzle checks that decide whether the rebuild is valid
First, the spray angle. The 150 in DLLA150P1712 is the spray cone angle in degrees, so the number is embedded in the model designation rather than a separate parameter to be looked up. Second, the hole count and hole diameter, which set the flow at a given pressure. Third, the opening pressure, set by the shim stack under the nozzle spring and measured on a pop tester or a common rail bench. Fourth, the needle lift, which is set by the injector body and the nozzle seat rather than by the nozzle alone. A nozzle that matches on angle and hole count but differs on opening pressure will deliver a different quantity at low pulse width, which is where idle quality is decided.
❓ FAQ: Nozzle Replacement Questions Buyers Actually Raise
Q1: Can I replace the nozzle and then just rewrite the old trim code?
A: No. The code describes the delivery of the complete assembly as tested. A new nozzle changes the delivery, so the old code no longer applies. The injector must be bench-tested and a new code generated.
Q2: What if my workshop has no injector bench?
A: Then the rebuild cannot be completed to a verified standard. The injector should be sent to a shop with a bench, or replaced as a complete assembly with a code issued for it.
Q3: Is the 150 in DLLA150P1712 the spray angle?
A: Yes. The number in the model designation is the spray cone angle in degrees, not a separate parameter.
Q4: What is the difference between opening pressure and needle lift?
A: Opening pressure is set by shims under the nozzle spring. Needle lift is a dimensional feature of the nozzle and body and is not normally adjusted by the installer.
Q5: Can a Liwei nozzle be fitted to a Bosch body?
A: It can be fitted, and it must be bench-verified, because the delivery curve is the product of the nozzle and the body together. Ask for delivery data at two pressures and two pulse widths.
Q6: What should the purchase order include?
A: The nozzle model with angle and hole count, the injector assembly number, the opening pressure specification, the clamp cap, the copper washer and the bench calibration requirement.
Core Competence

Warehouse Photo


Your doubts


Abosede Diesel

Customer feedback

Flexible Payment Methods for Your Convenience
To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer
Pay directly in 15 supported currencies.

Western Union
Quick and global money transfers.

PayPal
Safe and convenient online payment.

Alibaba
Enjoy extra protection with trusted Alibaba transactions.
We're here to make your order process worry-free - choose the payment method that works best for you!
Shipping Made Simple
We understand that every customer has unique shipping needs. That's why we offer:

Global Express Services
DHL, FedEx, UPS for fast and secure delivery.

Sea Freight Solutions
Affordable and efficient for bulk orders.

Flexible logistics
Prefer your own forwarder? We're happy to work with them too.
No matter the destination, we tailor the best shipping solution for you.
Hot Tags: DLLA150P1712 Nozzle for Bosch 0445120117 (XICHAI 6DN/6DF): Replacing the Nozzle Invalidates the Injector Trim Code, and No Scan Tool Can Recreate It, China DLLA150P1712 Nozzle for Bosch 0445120117 (XICHAI 6DN/6DF): Replacing the Nozzle Invalidates the Injector Trim Code, and No Scan Tool Can Recreate It manufacturers, suppliers, factory, DLLA151P2240 for 0445120277 0445120397, DLLA157P2508 for JAC 2 5L 0445110710, DLLA144P2610 for YUCHAI 0445110889, DLLA151P2244 for SISU 0445120235, DLLA150P2142 for 0445120182 0445120183 0445120242, G3S56 for 5284016 5365904
You Might Also Like
-

DLLA155P733 LIWEI Brand , Common Rail High Quality N...
-

DLLA152P898 LIWEI Brand , Common Rail High Quality N...
-

Liwei Brand Common Rail Nozzle G3S91 Diesel Fuel Inj...
-

Liwei F00VX40072 Piezo Nozzle for Bosch 0445116048/0...
-

Liwei Nozzle DLLA149P2597 Common Rail Diesel Injecto...
-

LIWEI Brand High Quality Common Rail Nozzle DLLA152P...



