CAT318 – Common Rail & HEUI Injector Test Bench
1. Product: CAT318
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: Original :ABOSEDE DIESEL
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
For a diesel repair shop, every hour an injector-related vehicle occupies a bay represents lost revenue opportunities, and every warranty comeback cuts directly into the thin margins of parts sales. The CAT318 is built to break that cycle-not by adding another piece of equipment to the floor, but by giving shop owners verifiable control over what leaves the bench and goes into the engine. This single workstation handles both solenoid and piezoelectric injectors from BOSCH, DELPHI, DENSO, and SIEMENS, covering the vast majority of common rail systems encountered in daily service traffic, while also accommodating HEUI units found in Caterpillar and Navistar platforms. It eliminates the guesswork that drives repeat repairs, allowing the shop to bill accurately the first time and move the next job in.
🛠️ Curbing Parts Float and Bench Delays
Maintaining a "known good" injector inventory for exchange programs is expensive, yet failing to verify returned cores leads to installing questionable parts and absorbing subsequent labor costs. The CAT318 shifts that risk by performing fully automatic detection on all electromagnetic solenoid injectors-BOSCH, DELPHI, DENSO, SIEMENS included-as well as every piezoelectric injector variant. It measures inductance to flag coil degradation before assembly, evaluates BIP (Beginning of Injection) response time to catch sluggish actuator behavior, and tracks AHE dynamic stroke to reveal plunger wear that alters injection timing. With rail pressure generation up to 2,600 bar sourced from a genuine BOSCH CP3.3 pump and flow metered by German ZDM and KRACHT sensors, the bench produces data that directly correlates with on-engine performance, enabling the shop to sort cores into "rebuildable," "reusable," and "scrap" categories before any vehicle enters the bay. This reduces the capital tied up in questionable inventory and compresses the diagnostic phase from hours to minutes.
💡 Eliminating Coding-Related Comebacks
Injector coding is routinely skipped or performed inaccurately because the necessary online interfaces are unavailable at the workbench. The CAT318 closes that gap by integrating OEM-spec coding generation into its standard test cycle. It produces BOSCH QR codes automatically, and through its live internet connection, generates DENSO QR codes, DELPHI C21 and C31, and SIEMENS (VDO) IIC directly on the unit under test. Without this step, the engine ECU continues applying calibration values intended for the previous injector, causing uneven cylinder contribution, elevated exhaust gas temperatures, and eventual DPF soot loading. By ensuring the corrected IQA (Individual Quantity Adjustment) data travels with the injector to the vehicle, the CAT318 preempts the sort of drivability complaint that typically surfaces 500 miles later, on someone else's shift, at full shop cost to resolve.
📊 Specifications That Drive Bay Efficiency
| Parameter | Specification | Workshop Impact |
|---|---|---|
| Rail Pressure Range | 0 – 2,600 bar | Covers current and emerging high-pressure systems without hardware upgrades. |
| Drive Motor | 5.5 kW (CR) / 3 kW (HEUI) | Supports continuous daily cycling without thermal derating. |
| Flow Measurement | ZDM + KRACHT sensors, ≤1% tolerance | Delivers repeatable pass/fail decisions, eliminating borderline judgment calls. |
| Pulse Width | 50 – 12,000 µs | Reproduces ECU pre-injection and main injection dwell times accurately. |
| Fuel Temperature | 40°C ± 2°C, active air/oil cooling | Maintains consistent oil viscosity, avoiding seasonal measurement drift. |
| Power Options | 220VAC / 380VAC, 50/60Hz | Adapts to existing shop electrical layouts with no costly upgrades. |
🔩 Turning Certainty into Faster Turnover
The core financial drain in diesel injection service is not the cost of the part itself, but the cascade of labor, towing, and customer dissatisfaction when a replaced injector fails to resolve the complaint. The CAT318 addresses this through remote assistance and online system upgrades, ensuring that as new injector part numbers and test routines emerge, the bench remains current without requiring a new capital outlay. Its integrated thermal management holds test fuel at 40°C ± 2°C, so flow measurements remain comparable across summer and winter shifts, and the 5.5kW drive motor handles back-to-back test cycles without losing rail pressure stability. For the shop owner, this translates into predictable test outcomes that align with on-engine behavior, reducing the frequency of "tested good, runs bad" scenarios and protecting the shop's reputation in a market where word-of-mouth referral remains critical.
❓ FAQ: Bulk Buying and Real-World Durability
Q1: When purchasing multiple units for a workshop chain, can calibration files be synchronized across locations?
A: Yes, the system supports centralized database synchronization via cloud backup, allowing all benches to access identical injector definitions and test plan updates.
Q2: Does the CAT318 accept remanufactured injectors with replaced nozzles or plungers?
A: Absolutely. The AHE and BIP measurements quantitatively detect plunger lift changes and solenoid response shifts, giving you hard data to approve or reject rebuilt units before they reach the customer.
Q3: What is the typical service life of the flow sensors under heavy daily usage?
A: The ZDM and KRACHT sensors are rated for continuous workshop duty, with exchange units available to minimize downtime when calibration service is due.
Q4: Can this bench identify subtle performance differences between new OEM injectors and aftermarket alternatives?
A: Yes, the flow tolerance of ≤1% and dynamic response measurements reveal delivery curve deviations that directly affect combustion quality and fuel consumption.
Q5: How are software updates delivered, and is there a recurring fee?
A: Updates are pushed via the built-in internet connection at no additional charge, ensuring new injector part numbers and test routines are added as they reach the aftermarket.



Flexible Payment Methods for Your Convenience
To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer
Pay directly in 15 supported currencies.

Western Union
Quick and global money transfers.

PayPal
Safe and convenient online payment.

Alibaba
Enjoy extra protection with trusted Alibaba transactions.
We're here to make your order process worry-free - choose the payment method that works best for you!
Shipping Made Simple

Customer reviews

Hot Tags: cat318 – common rail & heui injector test bench, China cat318 – common rail & heui injector test bench manufacturers, suppliers, factory
You Might Also Like
-

P7100, PW2000 Big Stopper – Precision Tool For Diese...
-

Kubota 3-Cylinder Transfer Case – Precision Power Di...
-

SIEMENS Measuring Tool & Shims For Common Rail Injec...
-

CP5 High‑Pressure Pump Conversion Adapter – Multi‑St...
-

HP0 Pump Plunger Repair Tools – Precision Service Ki...
-

Built-in Injector Return Liner Set BIRL-10 – 10pcs/Set


