Denso 095000-0582 Common Rail Injector for Hino S05C Diesel Engines
1. Product: 095000‑0582
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: ABOSEDE Diesel
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
This Denso common rail injector 095000-0582 is a direct-fit replacement for Hino S05C powerplants found in Dyna and Dutro chassis. Unlike generic aftermarket listings that recycle the same spec sheet, this page addresses what workshops actually verify before committing to a purchase: OEM cross-reference confirmation, core return economics, and the coding requirement that determines whether a unit will communicate with the ECU after installation.
🔧 OEM References and Build Specifications
The injector carries Denso 095000-0582 as its primary identifier, with Hino OEM 23910-1201 and S2391-01201 as the cross-references stamped on the original unit. It operates within a common rail direct injection architecture, delivering fuel at pressures commanded by the ECU rather than mechanical timing. The nozzle assembly corresponds to DLLA155P767 specifications, a detail that matters when matching spray pattern to the combustion chamber geometry of the S05C-TB engine. Each unit is supplied new (not remanufactured), fully tested on a common rail bench for back-leakage and electrical resistance before dispatch.
🛣️ Vehicle and Engine Coverage
| Application | Engine Code | Chassis | Notes |
|---|---|---|---|
| Hino Dutro | S05C-TB | 4.6L displacement | Euro 3 emission standard |
| Hino Dyna | S05C | Light-duty truck | Shared injector across 095000-0580/0581/0582/0583 supersession chain |
| Toyota Dyna | S05C | Export markets | Verify 23910-1201 stamp on original body before ordering |
The 095000-0580 and 095000-0581 suffixes are often listed as interchangeable, but the 0582 calibration may differ subtly in injection quantity mapping. If the original injector body shows S23910-01201C, this unit is the correct replacement; if the stamp reads 23910-1201A, confirm with the supplier before ordering.
🔩 Installation and Coding Requirements
These injectors require coding to the vehicle ECU using a diagnostic scan tool after installation. Without the IMA/ISA coding sequence, the engine may enter limp mode or exhibit rough idle despite the injector being mechanically sound. The copper combustion washer must be replaced every time the injector is removed; reusing a crushed washer risks compression leakage and carbon blow-by that mimics injector failure. Torque the injector clamp to the Hino specification-over-tightening distorts the nozzle nut and alters spray symmetry. Before fitting, verify that the fuel rail has been flushed; debris from a failed upstream pump will destroy the new control valve within minutes of first start.
📊 Repair Economics and Core Return Logic
For a diesel common rail repair shop, the decision to stock this injector hinges on core recovery. A $55 core deposit per unit is standard practice in this segment, refundable only when the original injector is returned complete and rebuildable. Remanufactured alternatives exist, but the S05C platform is sensitive to control valve wear-a reman unit with a polished but worn valve seat may pass a bench test and still cause hot-start hesitation under load. New units eliminate that variable. The practical service life of a genuine 095000-0582 under clean fuel conditions exceeds 150,000 km; premature failure almost always traces to water contamination or filter bypass, not the injector itself.
❓ FAQ for Repair Shops and Distributors
Q1: The original injector has no visible part number-how do I confirm fitment?
A: Measure the solenoid resistance (approximately 0.8–1.0Ω at 20°C) and compare the nozzle protrusion dimension against the S05C cylinder head specification. A 0582 unit will not interchange with the 0580 in applications requiring the later Euro 3 calibration.
Q2: Can I install this without coding the ECU?
A: No. The ECU stores injector correction codes that compensate for manufacturing tolerances. Skipping coding causes uneven cylinder contribution and triggers P0200-series fault codes.
Q3: What causes a new injector to fail within the first week?
A: Contaminated fuel entering the control chamber is the leading cause. Replace the fuel filter and inspect the high-pressure pump for metal debris before installation-otherwise the warranty is void.
Q4: Do you accept mixed orders with 095000-0581 for fleet stock?
A: Yes, but 0581 and 0582 must not be mixed within the same engine unless the ECU calibration explicitly permits it. Distributors should label stock by OEM suffix to prevent counter errors.
Q5: What is the return rate on this part for your workshop customers?
A: When coding and washer replacement protocols are followed, field returns fall below 2%; the majority of "defective" returns trace to installation errors rather than injector fault.




Flexible Payment Methods for Your Convenience
To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer
Pay directly in 15 supported currencies.

Western Union
Quick and global money transfers.

PayPal
Safe and convenient online payment.

Alibaba
Enjoy extra protection with trusted Alibaba transactions.
We're here to make your order process worry-free - choose the payment method that works best for you!
Shipping Made Simple

Customer reviews

Hot Tags: Denso 095000-0582 Common Rail Injector for Hino S05C Diesel Engines, China Denso 095000-0582 Common Rail Injector for Hino S05C Diesel Engines manufacturers, suppliers, factory, denso injector
You Might Also Like
-

095000‑6310 Common Rail Diesel Injector — High‑Preci...
-

095000-0760 Denso Common Rail Injector for Isuzu 6SD...
-

095000-6490 DENSO Common Rail Injector — Advanced Di...
-

295050-0810 / 23670-09380 / 23670-0L110 Common Rail ...
-

Rethinking Fuel Precision: Denso 095000-5190 Common ...
-

High-Performance Denso Diesel Fuel Injectors Models ...



