Bosch 0928400627 Fuel Metering Unit For CP3/CP1H Pumps
1. Product: 0928400627
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: ABOSEDE Diesel
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
The Bosch 0928400627 Fuel Metering Unit is an inlet suction control valve (SCV) engineered for CP3 and CP1H high-pressure common rail pumps. This normally-open solenoid valve governs the volume of diesel entering the pump's high-pressure chamber, directly influencing rail pressure stability across heavy-duty commercial platforms. As a direct replacement for 0928400617 and cross-referencing 1465ZS0052, 51125050027, and 5257595, it serves MAN, Cummins, Weichai, and Yuchai engine families operating under sustained load conditions.
🔧 Specifications That Determine System Response
The 0928400627 operates as a two-pin solenoid actuator mounted on the low-pressure side of the high-pressure fuel pump. Its 100-bar working pressure range and normally-open default position mean the valve remains fully open at zero duty cycle, allowing maximum fuel entry during cranking and immediately shutting flow when the ECU commands closure at key-off. This normally-open architecture distinguishes it from pressure-control valves on the rail, and technicians must recognize that a disconnected harness on this component floods the pump rather than starving it. The return spring inside sets the mechanical zero point-the spool position at 0% command-from which the ECU calculates every subsequent flow correction.
🛣️ Engine and Vehicle Platforms Covered
| OEM Reference | Engine Family | Vehicle / Equipment Applications |
|---|---|---|
| 0928400617 | MAN D2066 LF0, D2066 LF14 | TGA, TGS, TGX, TGM (2004–2020) |
| 1465ZS0052 | Cummins ISBe, QSB, ISLe | Medium-duty trucks, buses |
| 51125050027 | Weichai WP10, WD615 | JAC, Howo A7, heavy trucks |
| 5257595 | Yuchai, Komatsu | PC300-10, PC360-10 excavators |
This fuel metering valve is not engine-specific in the narrow sense-it calibrates to the pump platform. A unit that performs correctly on a CP3 pump in a MAN TGX will behave identically when installed on a CP1H pump in a Cummins ISBe application, provided the ECU software expects the same valve characteristics. That interchangeability is why the 0928400627 appears across such a broad spectrum of diesel platforms.
⚙️ Installation and Contamination Awareness
The valve mounts with two fasteners and a single O-ring seal on the pump body's low-pressure inlet. Before removal, verify that the fuel filter has been replaced within interval-the 0928400627 is a precision flow-control device, and debris that passes a degraded filter lodges directly in the spool bore. The connector must click audibly; a partially seated plug causes erratic duty-cycle feedback and triggers P0090 (fuel pressure regulator circuit) without any mechanical fault in the valve itself. After installation, clear adaptive fuel-pressure corrections and allow the ECU to relearn the hot idle duty cycle-a healthy 0928400627 typically settles between 18% and 25% at operating temperature on a CP3 pump.
💡 Why the Metering Unit Matters to Repair Economics
A failing suction control valve does not announce itself with a single clean symptom. The valve's return spring weakens gradually, the spool bore accumulates varnish, and the ECU compensates by driving higher duty cycles to achieve the same rail pressure. By the time P0087 (rail pressure too low) or P0088 (rail pressure too high) appears, the correction window has been exhausted and the vehicle enters limp mode or shuts down. Replacing the 0928400627 at the first sign of duty-cycle drift-before fault codes set-restores the pump's original flow calibration and prevents secondary damage to injectors and the pressure relief valve from prolonged pressure instability. For fleets and repair shops, tracking hot idle duty cycle at every service interval converts this valve from a reactive replacement into a predictive maintenance item.
❓ FAQ for Common Rail Repair Shops and Distributors
Q1: The duty cycle at hot idle has crept from 21% to 28% with no fault codes. Is replacement urgent?
Not urgent today, but plan it. A seven-point drift means the return spring is fatiguing. The ECU is still compensating successfully, which is why no code has set. Once the correction limit is reached-typically around 35–40%-the engine derates without warning.
Q2: Does a 0928400627 from one pump platform work on another, or are there calibration variants?
The valve is mechanically identical across applications. The calibration lives in the ECU software, not the valve. If the ECU expects a normally-open IMV with this spring rate and coil resistance, any genuine 0928400627 will work.
Q3: Can I diagnose a weak metering valve without a scan tool that reads duty cycle?
A simple fuel return-flow test can indicate a valve that isn't closing fully. With the engine at operating temperature, measure return flow from the pump. Excessively high return volume at idle suggests the spool is not seating, often due to spring fatigue or bore contamination.
Q4: What causes the valve to fail most often-electrical or mechanical?
Mechanical, overwhelmingly. The solenoid coil rarely fails. The dominant failure mode is spool sticking from diesel contamination-fine particles passing a degraded filter lodge in the bore, or varnish from poor fuel quality causes the spool to hesitate.
Q5: Do I need to replace the fuel filter whenever I install a new metering unit?
Yes. Installing a new valve into a contaminated fuel system is a guaranteed callback. The 0928400627 has clearances measured in microns. Any debris the old valve tolerated will destroy the new one within a short operating period.
Q6: What's the difference between this valve and a rail pressure control valve?
Location and default position. The 0928400627 sits on the pump inlet and is normally open. A rail pressure control valve mounts on the common rail and is typically normally closed. They regulate the same pressure but from opposite ends of the system.
Basic Information about the Company




Flexible Payment Methods for Your Convenience
To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer
Pay directly in 15 supported currencies.

Western Union
Quick and global money transfers.

PayPal
Safe and convenient online payment.

Alibaba
Enjoy extra protection with trusted Alibaba transactions.
We're here to make your order process worry-free - choose the payment method that works best for you!
Shipping Made Simple

Customer reviews

Hot Tags: bosch 0928400627 fuel metering unit for cp3/cp1h pumps, China bosch 0928400627 fuel metering unit for cp3/cp1h pumps manufacturers, suppliers, factory
You Might Also Like
-

Bosch F00VC5009 Ceramic Ball – Precision Component F...
-

0281020067 | Bosch MAN ECU – Electronic Diesel Contr...
-

Bosch Unit Injector Solenoid Clamp Nut – Eddy Curren...
-

F00BC80045 ECU – Hardware-Identical Platform With Mu...
-

04290102 ECU – Deterministic Real-Time Controller Wi...
-

0445226042 Common Rail – Acoustic Damping Characteri...


