Bosch Common Rail Injector 0445110280 for Renault 1.9 dCi F9Q Engines
video
Bosch Common Rail Injector 0445110280 for Renault 1.9 dCi F9Q Engines

Bosch Common Rail Injector 0445110280 for Renault 1.9 dCi F9Q Engines

1. Product:0445110280
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: BOSCH
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal

  • Fast Delievery
  • Quality Assurance
  • 24/7 Customer Service
Product Introduction

 

This Bosch common rail injector carries the 0445110280 (Bosch format 0 445 110 280) and is the solenoid-type CRI unit specified for Renault 1.9 dCi powerplants bearing the F9Q 816 and F9Q 818 engine codes. For a diesel repair shop, the decision to replace this injector rarely comes from a catalog lookup alone-it comes from a cylinder balance reading that won't settle, a leak-back test that fails the comparative threshold, or a cold-start crank that has stretched beyond what a fuel filter change can explain. The unit's job in the common rail system is narrow but absolute: meter fuel at rail pressures exceeding 1,350 bar and deliver it as a spray pattern the ECU can trust across every combustion cycle. When that trust erodes, the driver feels it before the fault code appears.

 

🔧 Rail Pressure Window and Spray Calibration Parameters

 

The 0445110280 operates within the hydraulic envelope Bosch designed for the F9Q's combustion chamber geometry. Its solenoid valve responds to injection commands in the sub-millisecond range, and the nozzle (aftermarket rebuild reference DLLA188P1620) determines the atomization quality that directly governs particulate matter output and combustion noise. What separates a serviceable unit from a scrap core is not the coil resistance alone-it is the consistency of the back-leakage rate across the operating pressure map. A bench test that passes at idle but drifts at 800 bar and above tells you the valve seat has worn past the point where ECU corrections can compensate. 

 

🛣️ F9Q 816 and F9Q 818 Fitment Boundaries

 

Engine Code Typical Host Models Production Window Critical Fitment Note
F9Q 816 Renault Mégane II 1.9 dCi 2005–2008 Confirm whether the vehicle carries the Euro 4 calibration; early and late F9Q 816 units use different injector hold-down clamp torque specs
F9Q 818 Renault Scénic II 1.9 dCi 2005–2008 Some Scénic II variants share the 0445110280 with Mégane II, but the ECU software version can affect whether the replacement unit's IMA code is accepted without a forced adaptation routine

A common counter error involves ordering by vehicle registration alone. The F9Q engine family ran across multiple Renault platforms and production years, and the injector specified for a 2006 Mégane II may not be interchangeable with a 2007 unit carrying a different engine management calibration. 

 

🛠️ Installation Protocol That Prevents Comebacks

 

Three procedural failures account for most premature failures of this injector in service. First, copper sealing washers are single-use components; reusing a compressed washer introduces compression blow-by that carbonizes the injector seat and mimics an internal fuel delivery fault. Second, the IMA coding step is non-negotiable on F9Q applications where the ECU requires per-cylinder correction input. Third, the fuel system must be flushed and the filter replaced before the new injector sees pressurized fuel-debris downstream of a failing filter will score the nozzle needle and destroy the spray pattern within a few thousand kilometers. A fourth point earns its place from field reports: after fitting, run a leak-back test on all four cylinders, not just the replaced one. 

 

💡 When This Injector Makes Economic Sense

 

The repair-order calculation for a F9Q 816/818 injector replacement is not simply "new versus used." It is a choice between a genuine Bosch unit and a remanufactured alternative whose solenoid and valve seat may have been replaced but whose nozzle was cleaned rather than renewed. For a vehicle in commercial service-a Scénic II used as a taxi or a Mégane II covering 30,000 km annually-the genuine unit's expected service window under normal fuel quality is in the 180,000–220,000 km range, whereas remanufactured units with reused nozzles tend toward 80,000–130,000 km under comparable conditions. For a low-mileage private vehicle facing a single injector failure, a properly documented remanufactured exchange can be defensible. The distinction that matters for a shop's reputation is traceability: a unit with a verifiable IMA code and a bench test report covering the full pressure map is a different product from a box with a sticker. 

 

❓ FAQ for Diesel Repair Shops and Parts Wholesalers

 

Q1: Can I fit 0445110280 to an F9Q engine that originally came with a different injector number?
A: Only if the ECU calibration matches. The F9Q 816/818 production window saw multiple injector variants across emissions tiers. Cross-referencing the Bosch number and Renault OEM reference is mandatory; assuming "F9Q means 0445110280" produces fitment errors.

Q2: What happens if I skip the IMA coding on an F9Q 816?
A: The ECU defaults to the previous injector's correction values. You will likely see rough idle, elevated smoothness correction values on that cylinder, and in some cases a stored fault for injection quantity adaptation. The engine may run, but it will not run correctly.

Q3: How do I tell a genuine Bosch unit from a relabeled aftermarket injector?
A: Check the laser-etched 10-digit number on the body for font consistency and depth, verify the IMA code on the head matches the documentation, and inspect the solenoid connector for the Bosch molding quality. Counterfeit units often fail the bench test at high-pressure points even when they pass a basic resistance check.

Q4: My customer's Mégane II runs fine after replacement but smokes on cold start. What should I check?
A: First, confirm the copper washer seated correctly and the hold-down clamp is at specification. Second, run a leak-back test on all four injectors-a worn neighbor on the same rail can skew cold-start fueling even with one new unit fitted. Third, verify the IMA coding was accepted by the ECU.

Q5: Do you supply the IMA code with the injector?
A: Yes. Every 0445110280 unit is supplied with its individual IMA calibration code documented for ECU programming. Shops that receive a unit without a matching code should not accept delivery.

Q6: What is the realistic service life difference between genuine and reman for a high-mileage F9Q?
A: Under normal fuel quality and filter maintenance, genuine units typically reach 180,000–220,000 km. Remanufactured units with renewed solenoids but original nozzles generally fall in the 80,000–130,000 km range. For commercial-use vehicles, the genuine unit's longer service window usually outweighs the initial price gap.

 

 

Basic Information about the Company

 

202510091606539026

 

 

2

3

4

 

Flexible Payment Methods for Your Convenience

 

To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

product-750-750

Bank Transfer

Pay directly in 15 supported currencies.

west union

Western Union

Quick and global money transfers.

PayPalLogo2014-1024x1014

PayPal

Safe and convenient online payment.

ae99cd49-2667-464e-b9db-b39cee0126e1

Alibaba

Enjoy extra protection with trusted Alibaba transactions.

We're here to make your order process worry-free - choose the payment method that works best for you!

 

Shipping Made Simple

6

Customer reviews

 

8

Hot Tags: Bosch Common Rail Injector 0445110280 for Renault 1.9 dCi F9Q Engines, China Bosch Common Rail Injector 0445110280 for Renault 1.9 dCi F9Q Engines manufacturers, suppliers, factory, bosch injector

You Might Also Like

(0/10)

clearall