Bosch 0445120080 Common-Rail Injector for Doosan DL06 & FAW 5.1/6.6L
1. Product:0445120080
2. Compatible Equipment: Diesel Fuel Injection Systems
3. Manufacturer: Aftermarket OEM Replacement
4. Condition: Brand New, Fully Tested
5. Origin: BOSCH
6. Shipping period: 3-5 business days
7. Payment terms: T/T, Western Union, PayPal
- Fast Delievery
- Quality Assurance
- 24/7 Customer Service
Product Introduction
The Bosch 0445120080 (0 445 120 080) is a CRIN2-series solenoid injector built for the 5.1–6.6 litre industrial diesel band. It serves as the direct fitment for Doosan DL06 / DL06S engines in DX225LC and DL200 excavators, and crosses to Doosan 65.10401-7004A, ZEXEL 107755-0280, and FAW truck references. This page answers what workshop buyers and fleet parts managers actually need to verify before committing stock: whether the number matches their engine plate, how to spot a counterfeit before installation, what realistic service life looks like in excavator duty cycles, and when replacement beats cleaning.
🔧 Specification & Cross-Reference Data
The 0445120080 operates as a normally-closed solenoid valve within the common-rail circuit, metering fuel on the high-pressure side before the nozzle needle lifts. The table below consolidates the identification data that matters at the parts counter: the numbers stamped on the injector body, the OEM crosses that confirm fitment, and the physical envelope for inventory planning.
| Parameter | Specification |
|---|---|
| Bosch P/N | 0445120080 / 0 445 120 080 |
| Injector family | CRIN2 (solenoid, high-pressure common rail) |
| Doosan / Daewoo cross | 65.10401-7004 / 65.10401-7004A |
| ZEXEL cross | 107755-0280 |
| FAW catalog reference | 1112010B470-0000 / 111201-0470 |
| Engine displacement band | 5.1 L / 5.9 L / 6.6 L |
| Unit weight (boxed) | ~0.65 kg |
| Fuel compatibility | Diesel, ultra-low sulphur recommended |
🚜 Machine & Engine Coverage in the Field
This injector concentrates in Doosan DL06 and DL06S power units fitted to the DX225LC tracked excavator and DL200 wheel loader-machines that spend their shift at 1,400–2,000 rpm under variable load, not steady highway cruise. On the truck side, it appears in FAW Jiefang D-series platforms running the 5.1 L and 6.6 L diesels, where the same injector must cope with longer idle periods and more frequent cold starts than an excavator typically sees. The practical takeaway for a mixed fleet parts operation: one stock line covers both a construction duty cycle and a regional haul duty cycle, but the failure modes differ-excavator injectors trend toward nozzle carbon accumulation from sustained part-load, while truck units more often show return flow drift from thermal cycling.
🛣️ Installation Sequence That Prevents Comebacks
The single most common installation error with the 0445120080 is reusing the copper combustion washer and failing to ream the injector bore. Carbon left in the seat distorts the nozzle tip angle by a few thousandths of a millimetre, which is enough to change spray targeting and produce a light-throttle haze the customer will notice before the bay door closes. The correct sequence: extract the old injector, run the bore brush and seat cutter, blow out with dry compressed air, fit a new copper washer and O-ring kit, torque to the Doosan/FAW specification, then program the IQA / trim code from the new injector body into the ECM. If the ECM retains the old trim value, the controller will mis-calculate injection quantity and the engine may idle smoothly while still flagging an imbalance code under load.
💰 When This Injector Makes Economic Sense vs. Cleaning
A CRIN2 injector with high return flow cannot be rescued by ultrasonic cleaning alone. The cleaning removes nozzle deposits but does nothing for worn control valve seats or a solenoid armature that has lost its response crispness. The decision threshold that experienced diesel shops use: if return flow exceeds roughly 50 ml/min on a bench test, or if the injector shows a cylinder balance deviation greater than 3–4 mm³/stroke at idle on a diagnostic scan tool, replacement is the cheaper path. Cleaning costs labour and still leaves a unit with marginal hydraulic authority. A fresh 0445120080 restores the rail pressure rise rate the ECU expects during hot cranking-the symptom that most often brings a DX225LC back to the shop in the first place.
❓ FAQ for Diesel Repair Shops & Parts Wholesalers
Q1: A customer's DL06S cranks fine cold but struggles hot. Is 0445120080 always the culprit?
Not always, but it is the first suspect. Hot-crank hard start on CRIN2 systems usually traces to injector return flow exceeding the rail pump's ability to build pressure at cranking rpm. Confirm with a leak-off test before quoting injectors.
Q2: How do I verify a genuine Bosch unit before installing it?
Check three layers: the embossed Bosch logo on the solenoid cap must be crisp and raised, not printed; the Data Matrix code above the solenoid must be laser-etched and scan as production data, not a generic QR; and the IQA code must be unique to that injector-if two units in the same batch share a trim code, stop.
Q3: Will this injector fit a 2008 FAW Jiefang with the 6.6L engine if the old unit shows 107755-0280?
Yes, the ZEXEL 107755-0280 cross confirms the 0445120080 as the Bosch equivalent. Verify the engine plate displacement and the number laser-etched on the old injector body before ordering, as FAW used more than one CRIN2 variant across model years.
Q4: What is a realistic replacement interval in excavator service?
Doosan DL06 excavators running typical earthmoving cycles generally see 2,500–4,000 hours before injector balance degrades enough to affect cold-start behaviour or fuel consumption. Machines that idle extensively or run on high-sulphur fuel trend toward the lower end.
Q5: Do I need to replace all six injectors if only one fails the bench test?
Not automatically, but on high-hour engines the remaining units are usually close behind. If the failed injector shows control valve seat wear rather than isolated nozzle carbon, the others share the same fuel history and will likely follow within a few hundred hours.
Q6: Is the IQA code programming mandatory after installation?
On Doosan and FAW applications using this injector, yes. The ECM uses the trim code to correct for unit-to-unit flow variation. Skipping programming will not prevent the engine from running, but it will leave the cylinder balance correction at the old injector's values, which can produce a persistent smoothness complaint.
Basic Information about the Company




Flexible Payment Methods for Your Convenience
To make your purchasing experience smooth and easy, we offer a variety of secure payment options:

Bank Transfer
Pay directly in 15 supported currencies.

Western Union
Quick and global money transfers.

PayPal
Safe and convenient online payment.

Alibaba
Enjoy extra protection with trusted Alibaba transactions.
We're here to make your order process worry-free - choose the payment method that works best for you!
Shipping Made Simple

Customer reviews

Hot Tags: Bosch 0445120080 Common-Rail Injector for Doosan DL06 & FAW 5.1/6.6L, China Bosch 0445120080 Common-Rail Injector for Doosan DL06 & FAW 5.1/6.6L manufacturers, suppliers, factory, bosch injector
You Might Also Like
-

Bosch 0445110788 — Common-Rail Fuel Injector (CRI1-18)
-

Bosch Injector 0445120302 for Cummins ISLe/ISDe & Me...
-

Diesel Fuel Injector 0445110738 For JAC – Compatible...
-

Injector 0445120054 New High-Quality For Bosch Repla...
-

Bosch 0445110628 Injector for Isuzu 4JB1-TC Diesel E...
-

Bosch 0445120385 Injector for Mercedes OM471: What S...



